Wind, Antennas, and a First Portable Session

This week I had two radio firsts: trying to put together a halfway decent antenna, and a first portable operating session.

I started by putting together a center insulator a dipole antenna. There are many possible designs online, but I ended up making one with materials I’m familiar with. It’s made of a 1″ PVC cross, four PVC caps, three 1/4″ eye-bolts, some nylon lock-nuts, and panel-mount BNC connector. The whole went together in about half an hour. The PVC connections were surprisingly tight as a press-fit, but they and the eye-bolts are secured with lock-tite and sealed with hot-snot just in case. The BNC connector is soldered internally to a couple pieces of hookup wire, which you can see poking out the sides of the cross. The antenna wires themselves are simply tied to the eye-bolts and wire-nutted to the hookup wire.

IMG_0587.JPG
The dipole center-support. This picture was taken after the fact, hence the pre-cut Nylon cord wrapped around it. You can see the two copper hookup wires poking out either end.

The dipole center, a 200′ spool of nylon wire, some “stakes” for securing the antenna to the ground (really, 8″ pegboard hooks, on sale at Menards!), some zip-ties, and a couple of rice-filled socks as counterweight all fit handily into this small plastic case I had lying around:

IMG_0588

I live only about a mile from Lake Michigan and the beautiful lakefront park space that runs along the East side of Chicago. I figured with the sunny-but-chilly weather we’ve been having this week, the lakeshore on a weekday afternoon would be pleasant to work in and not too packed with people.

I couldn’t find a suitable table or bench close enough to trees to set up under, but then I spotted the convenient height of the sea-wall between the outer lakefront trail and the lake itself. I couldn’t have been any closer to the lake without getting my socks wet!

IMG_0585.JPG
The operating position. There’s a little ledge just on the other side of this wall that was perfect for standing on.

I strung up a portable, homemade 40m dipole (wires cut in advance) as high as I could could into one of the nearby trees – I only got the center maybe 20 feet in the air, but that’s still better than the 8′ the random wire in my home office is. The ends are tied off to stakes near the ground. This made the setup more of an inverted-V than a true-dipole.

IMG_0582.JPG
One of the antenna-wires staked off to the ground. You can see the black coax sloping from the tree to the operating position.

The antenna is fed from ~60′ of RG-58, running into a ZM-2 Tuner for matching, and then via a short RG-58 jumped into the Virgin Receiver. I also brought along the ardiuno-controlled, Si5351-VFO I’ve been working on to allow for the ability to change frequencies, as detailed in my last post. If I’m going to spend the time setting up practically in a lake, I thought it would be nice to actually scan the whole band. Since the VFO rig is still on a breadboard, I was quite spread-out over my little stony operating station.

IMG_0577
Visible here: the coil of coax coming from the antenna; the Virgin Receiver, open to allow the VFO to interconnect; the breadboard with the Si5351 VFO on it; two separate 12V SLA batteries; some nice comfy headphones; and the large red cable-coiler I used to store the dipole wires (a bit overkill).

So now, the moment of truth – I hooked up the batteries, connected the receiver and VFO, did a quick by-ear tune on the ZM-2. I’ve never done something like this before – would it actually be better than my office random-wire? Was it all just a jaunt in the park? In short, would it work?

LIKE HECK IT WORKED!

Especially up in the SSB portion of the band, there were some stations that might as well have been on the other end of a phone call. (This, by the way, confirms that the Virgin can receive SSB and AM as well as CW.) In no particular order, I heard:

  • N8KKR, KA9ZXN and others on the Hams for Christ net on 7.263 (330p Central, Monday-Sat). Not my personal bag, but they seemed a very pleasant bunch.
  • W9DCQ and W4LWW having a nice QSO, between the two of them and some other operators I couldn’t quite copy.
  • KG9O and KK4FZI having a friendly chat.
  • Some other snippets of stations.

The listed stations alone include QTHs in Evergreen Park IL, Columbus OH, Middleton WI, Franklin TN, Grassy Creek NC, and Marion IN. None of them terribly far away in radio terms (the Tennessee locations is farthest at ~500 miles), but a great confirmation that the antenna was clear and working. With a height above the ground of less than 1/4 wavelength, the ideal dipole should have a high takeoff angle and be fairly omnidirectional, and that seems plausible based on results.

In sadder news, I seem to have broken some part of the WSPR functionality of my VFO in consolidating that functionality from two separate programs into one. 1W into the antenna and several repetitions netted be exactly zero receptions, either into this antenna or my office random wire. So it’s back into the code I go. While I’m at it, it would really be worth packaging up the little VFO into its own enclosure – having all those wires flapping about is a bit worrisome for transport!

All in all, a tremendously successful, if very chilly, day by the lake. Now that I know what I’m doing, I suspect it would be able to have the station set up and listening in about 10 minutes, and about the same for tear down. With the days getting warmer all the time, I’m sure I’ll be out there again soon.

Hear you on the air!

73

Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s