Hamfester’s Hamfest 2016

About a month ago, I attended the Hamfester’s Hamfest in Peotone, IL, south of Chicago. Sponsored by the Hamfesters club out of Crestwood, IL, we had a lovely day for it, if only a little muggy.

Hamfester’s had the most vibrant flea-market area of any of the fests I’ve been to so far. No lack of boat-anchor rigs to be sure, but also some newer ones for sale (an FT817, A TS450, a couple ICOM base stations). Lots of CW keys, and no lack of miscellany, but the “clear out the shack properly” contingent was definitely in full swing. They’re the ones who have new and interesting things, or spare rigs they don’t need, or tools.

IMG_1155
50 bucks for an old tube receiver. Wonder if it works?

There are several sellers that I’ve seen two or three times now – I’d be willing to bet they acquired either surplus hardware or an estate-sale or two, and now just want to be rid of all the parts. There’s one table that I make a point of picking through. It’s literally just a giant pile, but I’d found a couple little treasures in there…

IMG_1168
The Big Pile!

As I’ve previously mentioned, I didn’t come home with a huge haul from this swapmeet, but I did snag an unbuilt Scout Regen receiver kit that I put together. I also got a nice 30V adjustable, 500mA regulated current-limitted power supply from Elenco, in a nice case with leads, for 15 bucks. And a dual variable-cap from The Big Pile.

IMG_1169

See you at the Fest!

73

The Scout Regen

Last weekend, At the Hamfester’s Hamfest in Peotone, IL, I picked up a little Scout Regen kit from a fellow ham. The gentleman I bought it from was just lamenting to a friend “Nobody builds anything any more…,” but when I walked up to check out the un-built kit, he added, “….except this guy!”

It was unbuilt, but the metal frontpanel already had its decals applied (or perhaps pre-printed?), which was a nice place to start. I don’t have a great track record when it comes to applying decals and labels.

IMG_1169
The un-built Scout Regen kit, sitting atop the variable power supply I also found in Peotone. Also included: a ganged variable capacitor for future experiments.

The overall build took about 2 hours. The Scout Regen Builder’s Manual from the QRPKits website is very thorough, and was easy to follow. The only issue I ran into was a missing 5pF cap for the detector section. I substituted two 10 pF NP0 caps from my stock, soldering them in series before installing them in the PCB. Additionally, after completing the first part of the detector section (basically, everything installed but the coil and the power switch) the current drain had jumped to 20 mA. After finishing the build, the current dropped back to under 10 mA. How odd.

IMG_1183
The completed Regen receiver kit.

Listening with this kit is a lot of fun. Regen control is smooth, but very narrow; I may replace the regeneration control knob with a larger one. There’s all kinds of interesting things in the span of the receiver. Shortwave stations, the 80m and 40m hand bands, I found a couple different “WLO” beacons… really nifty. It’ll be nice to put on in the background while working on future projects.

Hear you on the Air!

73

DeKalb Hamfest 2016

I’ve been trying to think how long its been since I’ve been to a ham radio swapmeet. Certainly the last one I visited was the Electronics Flea Market at De Anza College with W6KWF sometime during my college days. So it’s been a good long while, and it seemed time to rectify that. And thus, I’m just back from the DeKalb Hamfest. First some details, and then I’ll get to today’s haul. A bit of a long post today, but there’s much to tell.

A brief overview – the DeKalb Hamfest is hosted by the KARC – the Kishwaukee Amateur Radio Club – and overseen by Bob W9ICU. It’s hosted at the Sandwich County Fairgrounds in Illinois around this time (early May) each year. $8 for admission, and easy parking.

IMG_0687.JPG

It wasn’t a huge event – maybe 10 or 12 indoor vendors and perhaps three times that many tailgate-ers. The indoor vendors, while they had lots of nice products, didn’t particularly entice me, as I think you could find just as good value on, say, banana-jack-to-BNC tails or audio connectors anywhere online. There was one vendor with a huge spread of every RF adapter and then some, as well as individual toroids for sale, including some big 100- and 240- size ones in unusual mixes. I’ll look for them at future fests.

IMG_0696.JPG
RF adapters and connectors for miles.

The tailgate-ers were more my speed, though none of the big-ticket items were really what I was looking for (or in my price range) Several old Heathkit receivers and transceivers for sale ($200-$600), lots of microphones, mobile units, CB radios. A few newer items, but mostly old tube equipment. At least four tables had the same Heathkit GD-1B Grid Dip Meter, which I found curious. Lots of vibroplex keys marked over $100.

But lots of treasures too. Maybe only three or four tables with proper parts bins, but I spent a good couple hours pouring through these to find some treasures. Most table owners were happy to make small talk and chat about their projects and where their goodies came from. I had a really laugh chatting with some of the nice folks running the tables, while piling up the day’s haul.


And what a haul!:

IMG_0705

Here’s the short list, starting at the bottom-left and working clockwise:

  • A pack of five unlabeled compression trimmer capacitors. These turned out to have a range of about 2-25pf.
  • A bag of ~10 small toggle switches with assorted mounting hardware. These range from SPDT to DP4T.
  • A large bag of ~20 rotary pots of assorted values, with a few rotary switches thrown in for luck.
  • A couple RG-58 jumpers with BNC connectors (free!)
  • A large air-spaced variable capacitor – unlabeled, turned out to be about 28-152pF. More on this below.
  • A nicely boxed step-attenuator with 50-ohm input/output impedance. I’d been thinking about building one of these, but running across one of them at the fest (for only $3) was a dream! It has a maximum of 59 dB of attenuation in steps of 20, 20, 10, 6, and 3 dB, as well as a variable attenuator (“3 dB?”) for fine tuning. It has Walter Schwartz’ name on the bottom, who was the nice gentleman who sold it to me. A very cool older ham.
  • A mysterious silver box… more on this below as well.
  • A bag of twenty 47pF NP0 capacitors. For future oscillators.
  • A couple bags of trimmer pots. One bag had five 500 Ohm trimmers, the other turned out to have a mix of 1K and 1M trimmers. I have these in mind as balance pots for diode mixers, but we’ll see where they end up.
  • A couple vacuum-molded packs of trimmer capacitors, 10-. These actually came from the Fry’s Electronics in Downer’s Grove – I couldn’t resist a visit on my way back to Chicago. And I got to help a dad pick out resistors for his ten-year old’s first electronic’s project. Neat!

All of the above for less than $20 total. Hamfest, for the win.


I’m particularly excited about the air variable capacitor. After a big of digging around, I pulled this one out of a cardboard box burried underneath a giant box of tubes:

IMG_0716.JPG

Since I didn’t have either a multimeter or an LCR meter with me, I had to make my best guess as to the voltage rating and capacitance of this unit. When I got it home, it turned out to have a capacitance that varies from about 28pF fully open to 152pF fully closed, with stops at either end. The plate spacing (measured with a caliper) is about 0.060 inches, which means it should start to arc-over at around 2400-2600V.

I have a specific project in mind for this guy: building a small transmitting loop antenna. A range of ~28-150pF should be enough to tune a 10′ circumference loop for the 20m, 17m, 15m, and 12m bands, as well as the 10m and 30m bands with a little fudging (this according to the 66 Pacific Loop Antenna Calculator). With some added capacitance in series or parallel and it could possibly be pushed to 10m, 40m, or 80m bands with reduced efficiency. The air-variable capacitor is key here, since it seems the voltages in a loop antenna can peak over a Kilovolt with just 10-20W of output power! In any case, more thoughts on that antenna as it comes together, but for now I’m drawing ideas from AA5TB, Nonstop Systems, KR1ST, W8JI, and VK3YE’s various projects.

In any case, one of the nice things about this particular air-variable is the reduction drive on it. You can see the worm-gear and larger reduction gear in the picture above – it takes 46 full revolutions of the small stud to shift the capacitor full fully open to fully closed. With a difference of 122pF between the two extremes of the capacitor, that’s an average of 2.7pF per revolution. Even using the bamboo-stick tuning method used by KR1ST (to avoid detuning the antenna by getting close to it), if I can manage rotational accuracy to about 10 degrees of the tuning stud, that’s a resolution of .07pF. Not bad!


One of the things I was on the hunt for this morning was a metal chasis or two to mount projects in. As nice as the Virgin Receiver turned out, I was hoping to find something a little more robust for future projects – maybe some old CD-drive casing or a gutted something or other. There wasn’t a whole lot of that sort of thing around, even in the big-piles-O’-parts, but then this silver beauty caught my eye.

I could see a couple of tubes inside, and from the ‘RCA’ and 1/4-inch jacks on the back (an no jack for a key or mic) I had a pretty good guess it was some kind of receiver, but other that, it seemed like a gamble. When I asked the owner of the table what it was, he very gamely said “I have no clue, but for $2, it’s yours!”

Well, at that price, it’s worth it just for the box! And what I found inside is definitely worth more than two bucks to me:

Judged by the two parts labelled “10.7 MCycle Interstage”, I feel pretty confident that this was indeed a receiver of some kind. More than half of the tube-sockets are empty, so I don’t think it’s worth trying to figure out what they were and bringing this thing back to life.

But check out the nifty components! Up front is a 4.5:1 vernier reduction drive, controlling a two-section air-variable capcitor for some kind of tuning. There’s a 30pF NP0 trimmer cap and a coil mounted directly to the air-variable, which is interesting. There’s a couple of 500K log-scale pots, a bunch of high-voltage capacitors, some old carbon-composition resistors, miniature RF chokes… this thing is going to be a great source of parts, as well as a keen chassis for a future project. Perhaps a regenerative receiver? I could see leaving that classy vernier drive capacitor in place as is and working around it…. hmmm….

Hear you on the air, and see you at the fest!

73