Si5331-Driven Transmitter – Beginnings

In Spring, a young man’s fancy turns to thoughts of transmitters. Having recently completed a receiver, and with the weather starting to warm a bit, I’ve got an itch to actually get on the air and talk back to the stations whose code I can now (slowly, painfully) decode.

Re-purposing some hardware and code from my DDS VFO project, I’ve been working on on a digitally controlled CW transmitter based around an Si5351. This is by no means an original thought, and my designs are largely based on Qrp-Labs’ Ultimate3s Kit. You can check out that original design over on the QRP-Labs site, under the PCB assembly instructions.

Essentially, this transmitter uses an Si5351 DDS clock chip to directly synthesize the desired output frequency, at up to 200 Mhz. This frequency is then amplified by a simple FET amplifier to approximately a 1W output level, then passed through a low-pass filter and out to an antenna. The Si5351 is controlled over i2c by an Arduino Uno, which has an attached LCD, a rotary encoder, and a couple buttons for frequency and band control. The updated code for this project is on Github.

Here’s a block diagram of the transmitter:

Si5351TransBck-3-6(3).png

The nice thing about this design is that the main frequency-dependent component is the low-pass filter; the Si5351 should be stable enough for CW contacts up to at least 50MHz. (Without an ovenized environment for the reference clock or some GPS disciplining or similar, there’s still a little drift and inaccuracy, but I don’t think it will be noticeable.) Above HF, I’d expect to see diminishing returns from the FET amplifier. But switching HF bands should just mean switching LPF filters and pressing a button on the VFO.

Here’s the circuit as constructed, up to where the LPF would go:

CW Transmitter sCHEMATIC
The simple Si5351-based transmitter, with a 3-FET amplifier.
Let’s walk through the circuit starting from the signal generator and working out toward the antenna. The output of CLK0 on the Si5351 is coupled into the amplifier with a 100nF cap. This drives the gates of three J110 FETs, and is biased upward by a voltage divider formed by a 10K pot and a 4.7kOhm resistor between 5V and ground. The power end of this voltage divider is bypassed to ground with a 100nF cap.

Power for the amplifier is fed from a nominal 12V (or lower) through an RF choke, in this case 25T on an FT37-43, into the FET drains. A 100nF cap here helps further bypass RF to ground at this point. Output is taken off the drains through a final 100nF cap. The FET sources are grounded.

While an actual RF transistor like a BS170 would likely be ideal, I had a bunch of J110 FETs in my bin after my last trip to California, so that’s what I used. They’re only rated for about 300mW dissipated power, so I’ll need to be careful with my heat sinks and duty cycle until I can replace them with something a little more sturdy.

IMG_0393
Three J110 FETs with their heat sinks on a piece of copper clad. In the back you can see the PA power coming in through the black alligator clip via the small RFC. The bias pot is on the left, signal comes in on the red wire on the bottom, RF out via the BNC connector on the right. The big white box down in the bottom is a 51 Ohm, 5W resistor I was using as a basic dummy load for testing
Preliminary results are encouraging – I hooked the output of the above circuit directly to a dummy load with no low-pass filter and ran the clock generator at 7.050MHz. I assessed power by reading off the peak voltage on an oscilloscope.I started with just 1 J110 and a 5V PA supply instead of 12V. This yielded about 9V peak-to-peak, or 200mW into 50 ohms. Installing the other two J110s bumped the output up to 10V P-P, or 250mW. Finally, after installing heat sinks on the FETs for safety and taking the supply voltage directly from a 12V SLA battery (~13.2V), the output hit 22V P-P, or 1.2W into 50 Ohms.   This last reading was verified with the power meter on an MFJ versa tuner.

IMG_0376
The transmitter spread out on the bench, with the display and Arduino at the top, the amplifier visible on the copper-clad in the middle, and a bulky MFJ tuner at the bottom acting as dummy-load and power-meter.Power provided by the 7Ah, 12V SLA battery at top-right.
I’ll need to put a little elbow grease into low pass filters before putting this on the air, because even on a scope the signal looks a bit gnarly. But first the first time, I’m responsible for 1W of Homebrew RF power. Watch out!

73

 

Advertisements

2 thoughts on “Si5331-Driven Transmitter – Beginnings

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s